Residential · New Orleans, LA
A damaged screen frame can sag, pop loose, or stop sealing against insects. Elite Screens New Orleans restores and replaces screen frames with square, tight-fitting assemblies that open, close, and latch correctly, serving New Orleans since 2017.
Every screen frame repair starts with a fit and square check so we fix the cause, not just the symptom. We measure diagonals for racking, inspect corner keys, hinge and latch points, and confirm the opening is plumb before we build or tune the frame. Depending on what we find, we straighten minor bends, replace worn spline channels, or build a new frame from aluminum screen frame stock cut on a miter saw with a stop block for consistent lengths. Hardware gets addressed at the same time, including spring-loaded plungers, pivot pins, slide bolts, and knife latches, so the finished panel sits flat and operates smoothly.
In New Orleans, screen frames take a beating from humidity, salt air, and wind-driven rain, which can accelerate oxidation, loosen fasteners, and swell surrounding wood. We commonly replace corroded corners and upgrade to stainless steel screws where appropriate, then set corners tight so the frame does not twist under tension. Screen material is matched to the use case, fiberglass for most openings, aluminum for added rigidity, pet-resistant mesh for high-traffic doors, and No-See-Um mesh for small insects. Clean edges matter, so we install fresh spline (typically 0.125-0.175 inch based on groove fit), roll it in with a spline roller at even tension, and trim cleanly for a crisp finish that does not fray or ripple.
Customers choose us because we show up prepared to solve the whole screen frame problem in one visit when possible. Our trucks carry aluminum frame extrusions, corner keys, spline sizes, rollers, and common replacement hardware, which speeds up repairs and reduces repeat trips. You get clear options, repair the existing frame when it makes sense, or replace it when the frame is out of square, cracked at the corners, or the channel is too worn to hold spline. We are licensed and insured, and we keep the work straightforward with a written scope and a clean jobsite.
Before we wrap up, we do a walkthrough and test the screen frame the way you use it. We confirm even reveals, smooth swing or slide, positive latch engagement, and a snug seal without rubbing or binding. You receive a free written estimate up front, material and mesh recommendations for your specific opening, and a finished screen that sits square and stays tight. If multiple panels are involved, we label frames as needed and verify consistent sizing so future rescreens and hardware swaps are simple.
Yes. We provide a free written estimate after measuring and confirming mesh type, frame condition, and attachment method.
In most cases, yes. We’ll identify the closest mesh type (fiberglass, aluminum, solar, pet-resistant) and match common colors like charcoal or black for consistent visibility.
We do both. If the frame is bent, corners are loose, or tracks and rollers are worn, we can repair or replace components so the new screen performs correctly.
Timing depends on enclosure size, number of panels, and whether framing repairs are needed. After an on-site measure, we’ll give a clear schedule with expected start and completion dates.
Yes. We work with property managers and businesses on patio enclosures, entry screening, repairs, and repeatable maintenance plans with consistent specs.
If your screen frame is bent, corroded, or constantly popping out, a quick rescreen will not fix the underlying fit. Elite Screens New Orleans provides screen frame repair and replacement for windows, screen doors, patio enclosures, and custom openings, focusing on square corners, solid hardware, and proper mesh tension. We inspect the opening, measure for racking, and determine whether the best value is straightening and tuning the existing frame or building a new aluminum frame to match the exact size and hardware layout.
Screen frames fail for a few predictable reasons: corners loosen, the frame racks out of square, or corrosion weakens the spline channel so the mesh cannot stay tight. We correct alignment first, then rebuild strength at the corners with new corner keys or reinforced connections where appropriate. When a replacement is the smarter route, we fabricate a new screen frame from aluminum screen frame extrusions, cut to length and assembled to maintain true 90-degree corners and consistent diagonals. That accuracy prevents bind, keeps the panel seated, and helps the latch engage without forcing it.
Mesh and spline are installed as a system. We recommend fiberglass for everyday durability, aluminum for rigidity, pet-resistant mesh for scratching and pushing, and No-See-Um mesh for smaller insects. After selecting the correct spline diameter for the channel, we roll it in evenly with a spline roller, balancing tension so the screen stays flat without bowing the frame. Clean trims and sealed corners keep the finished panel neat and longer-lasting in humid conditions.
Whether you need one screen frame repaired or multiple panels replaced, you get a clear scope, measurable fit improvements, and a final test in the opening. Contact Elite Screens New Orleans for screen frame repair and replacement in New Orleans, and we will provide a free written estimate and straightforward recommendations based on condition, cost, and performance.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in New Orleans. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
